skip to Main Content

DIY LED Grow Light

DIY LED Grow Light

The top reason many men and women get interested in'do it yourself' LED grow lights would be to spend less. Even low-end factory-made LED grow lights can cost approximately $100. As an alternative, you could buy a box of LED bulbs or even a COB for just about $10 -- $20, depending on which you are shopping. Standard LED drivers currently retail around the $20 -- $30 range, and heat sinks might be as low as $10.

Nevertheless, it is not just cheaper to build your LED grow light upfront. As you'll need to figure the output and input signal of your LED lights, you also are able to maximize the efficacy of your grow light setup. You can place as many or as few LEDs as you need, considering your perfect electricity expenses.

As another incentive, making your personal LEDs can be useful if you do not have a whole lot of space. You'll find it is a lot simpler to match your DIY components in tiny spaces versus most of those LED grow lights currently available on the industry. Just, enjoy a DIY grow tent, producing your own LED lights provides you with the greatest control over the qualities of your grow area.

Why Use LED Grow Lights

LED lights operate cooler than the rest of the lighting methods. Why is that significant? This means it's energy efficient and lasts for quite a very long time until it warms up or reduces vitality power. An LED may last for between 50k to 70k hours and after that, it reduces energy-strength up to 30%, which is still better than other forms. They work great for most indoor growers since they need to be left throughout. This means that you don't need to worry about enormous electric bills interchangeable with other lighting choices.

Another substantial reason to use LED grow lights would be, they are available in various colours with colour alternatives for blue and red lights that are significant in harvest life. Blue lights, as an instance, is significant in chlorophyll production and photosynthesis. LED grow lights help plants consume sufficient lights that are significant for growth and throughout the fruiting period.

Would You Require Experience to Build by own LED Grow Lights?

Since I wrote this guide, it is getting much, a lot simpler to construct your personal lights. The component that proved hardest in the first days was locating a heat sink to the DIY COB grow light, but currently there are all kinds of heat sinks accessible that come pre-drilled for an assortment of hot COBs, so that I think that it's well worth mentioning this and giving it a bit revamp. We are going to begin with analyzing how to construct your light the simple way, then take a look at the initial, more involved alternative, where you are drilling your heat sink.

Since I wrote this guide, it is getting much, a lot simpler to construct your personal lights. The component that proved hardest in the first days was locating a heat sink to the DIY COB grow light, but currently there are all kinds of heat sinks accessible that come pre-drilled for an assortment of hot COBs, so that I think that it's well worth mentioning this and giving it a bit revamp. We are going to begin with analyzing how to construct your light the simple way, then take a look at the initial, more involved alternative, where you are drilling your heat sink.

You do not require any previous electrical experience to assemble a habit LED light . On the other hand, the more you understand about abilities like soldering and chain wiring, the much more ordinary that this procedure is going to be for you personally.

The vital qualities you want to begin establishing your grow lights comprise patience, dedication, and a willingness to understand. If you set time into studying fundamental theories like voltage, string wiring, and soldering, then you need to feel comfortable with any motorist, LED, and heat sink to create your grow light setup.

Components

My parts list with this particular construct is as follows:

4x Citizen CLU048-1212 Gen. 6 COBs 4x IDEAL 50-2204-CT COB Holders 4x 120mm Pin-Fin Heat Sinks (all these are great for up to 60 watts -- should you push your COBs more difficult, you'll need larger heat sinks)

8x M3 Screws to secure COB holders to heat (those came together with the heat sinks) 1x Mean Well HLG-185H-C1400B LED Notebook 1x Thermaltake Thermal Grease -- TG4 2x Wago two Conductor Connectors 1x 100K Ohm Potentiometer 1x LLT-L20 Waterproof Power Connector with Power Cord

A Couple of Chunks of Red and Black 18 Gauge Wire

Each of the elements for the construct.

4x Citizen CLU048-1212 Gen. 6 COBs at 3000K color temperature.

4x 120mm Pin-fin heat sinks from Horticulture Lighting Group 4x IDEAL COB holders to your CLU048 chips.

A tube of thermal compound to help transfer heat between the COBs along with the heat sinks. 1 tubing does 4 COBs.

Wago 2-conductor lever nuts. These things are amazing.

A 100K ohm linear taper potentiometer.

This potentiometer came with a great cap.

A LLT-L20 watertight connector which I am using for the AC power link between the motorist and the wall socket.

A Mean Well HLG-185H-C1400B LED driver.

Here Is What I had for resources for this construct:

Wire Strippers

Screwdriver (I have used this butane version for many years and enjoy it)

Old Plastic Card to Spread Thermal Grease

Installing the COBs at COB Holders

The very first step is a simple one. Take your COB and fit it in to one of your COB holders. There is normally a springy small tab which you will have to depress, and also a few corners you will want to match your COB into. The rear of this holder will probably have a plus symbol to indicate which side you want to match with all the positive side of this COB. Front of this COB will possess this exact same symbol -- just be certain that you fit them up.

Apply Thermal Compound into the Rear of this COB

There are a couple of unique methods to do this. It's possible to use thermal compound, that's how I do this, or you could buy handy small thermal pads which are sized to your specific COB -- although these may be expensive. Should you proceed the thermal chemical route, Set a pea-sized level of it on the back of this COB and distribute it out with a classic plastic card:

Fasten the COB & Holder into the Heat Sink

If you have obtained the correct heat sinks for your specific version of COB, they are going to have come with pre-drilled holes which fit the mounting points of your own holders. When you line up the holder, be sure that not just perform the screw holes line up to secure down it, however, the screw holes for attaching an optional reflector also lineup.

Terminate Your Own LED Driver AC Link

If you are unfamiliar with working with power, consider devoting some assistance on the motorist terminations -- differently, do so at your own risk. Be certain everything is unplugged till you are 100 percent complete and sure everything is wired properly.

I actually enjoy the connector that I was able to complete for this particular instance as it is waterproof and gives excellent stress relief to the cable (if the cable gets tugged on, it won't tear it from this connector). It's possible to use a connector just like that I did, or some range of others such as a NEMA 5-15P or even IEC-style power connectors.

Seek advice from your driver's guide for advice on wiring the AC connection. Some could have information printed on the event of the motorist -- mine informs me that the brown cord is my lineup (hot), the blue wire is impartial, and the green wire is ground. Ensure to twist down the connections very closely whichever style connector you use, and also make certain that there are not any stray strands of aluminum which have the ability to stand out. I chased my driver into a single side of this connector, then attached my power cable into another side of this connector. I paired the black of the power cable into the brown of this motorist, the white of the power cable into the blue of this motorist (unbiased ), and the green of the power cable into the green of this driver (earth ). Ensure that you've correctly identified the colours of your particular power cord -- that they might not be just like mine.

Terminate Your Own LED Driver DC Link

The identical safety rules apply for the DC side of the motorist since the AC side. Get assistance if you are uncomfortable with this and make sure you double-check all of the links, then just power it on if you are positive what's done properly.

The DC side is far simpler than the AC side. Many men and women utilize Wago connectors to the DC side, and they are a breeze. Only strip the driver back output a little then snap them in to two individual Wagos. When you are ready to join all of your COBs, the optimistic side of this COB run is going to be connected into the favorable Wago along with also the negative side of this COB run will visit the negative Wago (we are using a string link in this construct ).

Terminate Your Own Dimming Potentiometer ("B" Style Drivers Only)

Should you purchase a Mean Well motorist which finishes with a"B" (e.g. an HLG-185-C1400B), then you will want to complete an external potentiometer onto it so as to dim the light. If you receive the"A" variant of the exact same driver, then it is going to include an integrated screw terminal which may be used to dim the motorist. Here is the way to completing an external potentiometer onto a B-type driver.

Robert Davis

What started as a personal experience to improve my overall health by growing my own food has turned into a mission to share my experience and my own research. Growing your own food and eating healthier food is something that everyone has to try.

Back To Top
×Close search
Search